| Last Modified: 11-29-2007 | 1.6 A | |
| Service Category: Vehicle Exterior | Section: Exterior Panels/Trim | |
| Model Year: 2008 | Model: Sequoia | Doc ID: RM0000018XP00AX |
| Title: EXTERIOR PANELS / TRIM: NAME PLATE: INSTALLATION (2008 Sequoia) | ||
INSTALLATION
1. INSTALL NO. 3 BACK DOOR NAME PLATE
|
(a) Clean the attachment surface. (1) Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel. HINT:
Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes. (2) Using a piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light. NOTICE:
Installing the No. 3 back door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape. (3) Using a non-residue solvent, clean the attachment surface. |
(b) Install a new No. 3 back door name plate as shown in the illustration.
Installation Position:
|
Mark |
Measurement (Along Surface) |
|---|---|
|
a |
99.2 mm (3.905 in.) |
|
b |
104.5 mm (4.114 in.) |
|
c |
98.6 mm (3.882 in.) |
NOTICE:
Install the No. 3 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 3 back door name plate up to 20 to 30°C (68 to 86°F) and install the No. 3 back door name plate.
2. REMOVE NO. 4 BACK DOOR NAME PLATE
|
(a) Clean the attachment surface. (1) Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel. HINT:
Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes. (2) Using a piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light. NOTICE:
Installing the No. 4 back door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape. (3) Using a non-residue solvent, clean the attachment surface. |
(b) Install a new No. 4 back door name plate as shown in the illustration.
Installation Position:
|
Mark |
Measurement (Along Surface) |
|---|---|
|
a |
112.8 mm (4.441 in.) |
|
b |
87.8 mm (3.457 in.) |
|
c |
113.9 mm (4.484 in.) |
NOTICE:
Install the No. 4 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 3 back door name plate up to 20 to 30°C (68 to 86°F) and install the No. 4 back door name plate.
3. INSTALL SYMBOL EMBLEM
|
(a) Clean the attachment surface. (1) Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel. HINT:
Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes. (2) Using a piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light. NOTICE:
Installing the symbol emblem with any double-sided tape remaining on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape. (3) Using a non-residue solvent, clean the attachment surface. |
(b) Insert the 2 pins into the back door panel and install the symbol emblem.
NOTICE:
Install the symbol emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the symbol emblem up to 20 to 30°C (68 to 86°F) and install the symbol emblem.
4. INSTALL NO. 1 ROOF SIDE MARK
|
(a) Clean the attachment surface. (1) Using an infrared light, heat the double-sided adhesive tape remaining on the rear door panel. HINT:
Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes. (2) Using a piece of cloth, rub the double-sided adhesive tape off the rear door panel while it is hot from the infrared light. NOTICE:
Installing the No. 1 roof side mark while any double-sided tape remains on the rear door panel may cause adhesion failure. Therefore, completely remove the double-sided tape. (3) Using a non-residue solvent, clean the attachment surface. |
(b) Install a new No. 1 roof side mark as shown in the illustration.
Installation Position:
|
Mark |
Measurement (Along Surface) |
|---|---|
|
a |
4.6 mm (0.181 in.) |
|
b |
19.5 mm (0.768 in.) |
|
c |
4.6 mm (0.181 in.) |
|
d |
4.6 mm (0.181 in.) |
|
e |
16.3 mm (0.642 in.) |
|
f |
4.6 mm (0.181 in.) |
NOTICE:
Install the No. 1 roof side mark in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the rear door panel and the No. 1 roof side mark up to 20 to 30°C (68 to 86°F) and install the No. 1 roof side mark.
5. INSTALL NO. 1 ROOF SIDE MARK
|
(a) Clean the attachment surface. (1) Using an infrared light, heat the double-sided adhesive tape remaining on the rear door panel. HINT:
Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes. (2) Using a piece of cloth, rub the double-sided adhesive tape off the rear door panel while it is hot from the infrared light. NOTICE:
Installing the No. 1 roof side mark while any double-sided tape remains on the rear door panel may cause adhesion failure. Therefore, completely remove the double-sided tape. (3) Using a non-residue solvent, clean the attachment surface. |
(b) Install a new No. 1 roof side mark as shown in the illustration.
Installation Position:
|
Mark |
Measurement (Along Surface) |
|---|---|
|
a |
4.6 mm (0.181 in.) |
|
b |
26.6 mm (1.047 in.) |
|
c |
4.6 mm (0.181 in.) |
|
d |
4.6 mm (0.181 in.) |
|
e |
16 mm (0.630 in.) |
|
f |
4.6 mm (0.181 in.) |
NOTICE:
Install the No. 1 roof side mark in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the rear door panel and the No. 1 roof side mark up to 20 to 30°C (68 to 86°F) and install the No. 1 roof side mark.
6. INSTALL NO. 1 ROOF SIDE MARK
|
(a) Clean the attachment surface. (1) Using an infrared light, heat the double-sided adhesive tape remaining on the rear door panel. HINT:
Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes. (2) Using a piece of cloth, rub the double-sided adhesive tape off the rear door panel while it is hot from the infrared light. NOTICE:
Installing the No. 1 roof side mark while any double-sided tape remains on the rear door panel may cause adhesion failure. Therefore, completely remove the double-sided tape. (3) Using a non-residue solvent, clean the attachment surface. |
(b) Install a new No. 1 roof side mark as shown in the illustration.
Installation Position:
|
Mark |
Measurement (Along Surface) |
|---|---|
|
a |
4.7 mm (0.185 in.) |
|
b |
33.6 mm (1.323 in.) |
|
c |
4.5 mm (0.177 in.) |
|
d |
4.4 mm (0.173 in.) |
|
e |
34.1 mm (1.343 in.) |
|
f |
4.5 mm (0.177 in.) |
NOTICE:
Install the No. 1 roof side mark in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the rear door panel and the No. 1 roof side mark up to 20 to 30°C (68 to 86°F) and install the No. 1 roof side mark.
|
|